Dropbox

What's new in this version:

- bgp - improved BGP VPN selection
- bridge - added warning log when "ageing-time" exceeds supported hardware limit for 98DX224S, 98DX226S, and 98DX3236 switch chips
- bridge - fixed FastPath when setting "use-ip-firewall-for-vlan" or "use-ip-firewall-for-pppoe" without enabled "use-ip-firewall"
- certificate - fixed bogus log messages
- chr - fixed public SSH key pulling when running on AWS
- console - added "/task" submenu (CLI only)
- console - added option to create new files using "/file add" command (CLI only)
- console - improved stability when doing "/console inspect" in certain menus
- console - improved stability when editing long strings
- console - improved system stability
- console - removed bogus "reset" command from "/system resource usb" menu
- console - rename flag "seen reply" to "seen-reply" under "/ipv6 firewall connection" menu
- console - replaced "fingerprint" with "skid" in "/certificate print"
- console - show Ethernet advertise, speed and duplex settings depending on configured auto-negotiation
- container - fixed invoking "container shell" more than once
- container - improved "container pull" to support OCI manifest format
- defconf - added CAPs mode script for wifiwave2 devices
- detnet - fixed interface state detection after reboot
- dhcp - changed the default lease time for newly created DHCP servers to 30 minutes
- dhcpv4-server - release lease if "check-status" reveals no conflict
- disk - improved system stability when removing USB while formatting
- ethernet - fixed half-duplex forced mode at 10Mbps and 100Mbps on ether1 for RB5009, Chateau 5G ax and hAP ax3 devices
- filesystem - fixed partition "copy-to" function
- firewall - added "connection-nat-state" to IPv6 mangle and filter rules
- health - added limited manual control over fans for CRS3xx, CRS5xx, CCR2xxx devices
- health - fixed bogus value reporting for CRS510 device
- ike2 - fixed minor logging typo
- ipsec - added error log message when peer ID does not match certificate
- ipsec - fixed packet processing by hardware encryption engine on RB850Gx2 device
- ipsec - refactor X.509 implementation
- ipv6 - added "valid" and "lifetime" parameters for SLAAC IPv6 addresses
- ipv6 - send out RA packet with "preferred-lifetime" set to "0" when IPv6 address is deactivated
- l3hw - improved route offloading for 98DX224S, 98DX226S, and 98DX3236 switch chips
- leds - disable LEDs after "/system shutdown"
- lte - capped maximum lifetime of SLAAC address to 1 hour
- lte - fixed CA band clearing on RAT mode change
- lte - fixed duplicate IPv6 route for lte interface when "ipv6-interface" setting is used
- lte - fixed LTE interface not showing up when resetting RouterOS configuration
- lte - fixed passthrough mode when used together with another APN for Chateau 5G
- lte - fixed R11-LTE-US in LTE passthrough mode
- lte - fixed R11e-LTE-US reporting of RSSI in LTE mode
- lte - fixed re-attach in some cases where module would stay in not-running state after network detach
- lte - fixed second modem halt on dual R11e-LTE6 setup
- lte - improved system stability when changing LTE interface configuration during network scan with MBIM modems (introduced in v7.8)
- mpls- fixed LDP "preferred-afi" parameter
- netinstall-cli - improved device reinstall on failed attempt
- netwatch - added "startup-delay" setting (CLI only)
- netwatch - improved ICMP status evaluation when no reply was present
- netwatch - limit "start-delay" range
- ospf - fixed processing of fragmented LSAs
- ovpn - added support for OVPN server configuration export and client configuration import from .ovpn file
- ovpn - improved system stability for Tile devices
- quickset - fixed displaying of "SINR" when value is 0
- rose-storage - added option to nvme-discover with hostname (CLI only)
- rose-storage - fixed crash on nvme-tcp disable
- rose-storage - fixed rsync transfer permissions
- rose-storage - various stability fixes
- route - fixed "dynamic-id" for VRF tables
- route - improved system stability when making routing decision
- route - show SLAAC routes under the "/routing route" menu
- route-filter - improved stability when matching blackhole routes
- routerboot - added "preboot-etherboot" and "preboot-etherboot-server" settings ("/system routerboard upgrade" required) (CLI only)
- sfp - added log warning about failed auto-initialization on RB4011, RB5009, CCR2004-1G-12S+2XS, CCR2004-16G-2S+, CCR2116-12G-4S+, CCR2216-1G-12XS-2XQ devices
- sfp - allow modules that hold "TX_FAULT" high signal all the time on RB4011, RB5009, CCR2004-1G-12S+2XS, CCR2004-16G-2S+, CCR2116-12G-4S+, CCR2216-1G-12XS-2XQ devices
- sfp - allow modules with bad or no EEPROM in forced mode on RB4011, RB5009, CCR2004-1G-12S+2XS, CCR2004-16G-2S+, CCR2116-12G-4S+, CCR2216-1G-12XS-2XQ devices
- sfp - fixed "rate-select" functionality on CCR2004-16G-2S+ and CCR2004-1G-12S+2XS devices (introduced in v7.8)
- sfp - fixed combo-ether link monitor for CRS328-4C-20S-4S+ switch
- sfp - improved module initialization and display more detailed initialization status on RB4011, RB5009, CCR2004-1G-12S+2XS, CCR2004-16G-2S+, CCR2116-12G-4S+, CCR2216-1G-12XS-2XQ devices
- sfp - improved SFP28 interface stability with some optical modules for CRS518 switch
- sfp - improved system stability with some SFP GPON modules on RB4011, RB5009, CCR2004-1G-12S+2XS, CCR2004-16G-2S+, CCR2116-12G-4S+, CCR2216-1G-12XS-2XQ devices
- snmp - fixed SNMPv3 "Reportable" flag behavior
- snmp - improved outputting of routes
- socks - added VRF support
- ssh - added Ed25519 host key support
- ssh - added support for Ed25519 key export and import in PKCS8 format
- ssh - do not allow SHA1 usage with strong crypto enabled
- ssh - improved service responsiveness when changing SSH service settings
- ssh - improved SSH key import process
- storage - mount RAM drive for devices with 32MB flash
- supout - added DHCP server network section
- switch - fixed ACL rules matching IPv6 packets when using only IPv4 matchers
- switch - improved system stability during rapid MAC flapping for 98DXxxxx switches
- switch - improved system stability for 98DX8208, 98DX8216, 98DX8212, 98DX8332, 98DX3257, 98DX4310, 98DX8525, 98DX3255, 98PX1012 switches
- timezone - updated timezone information from "tzdata2023c" release
- vrrp - added "self" value for "group-master" setting
- vxlan - added forwarding table
- vxlan - fixed packet drops when host moves between remote VTEPs
- webfig - added inline comments
- webfig - fixed "Destination" value under "MPLS/Forwarding-Table" menu
- webfig - fixed issue where "Certificate" value disappears under "IP/Services" menu
- webfig - fixed issue where entries might be missing under "IP/DHCP-Server" menu
- webfig - various stability fixes
- wifiwave2 - added "radio/reg-info" command to show regulatory requirements (currently implemented for 802.11ac interfaces) (CLI only)
- wifiwave2 - added ability to configure antenna gain
- wifiwave2 - added ability to configure beacon interval and DTIM period
- wifiwave2 - added information on additional interface capabilities to radio parameters
- wifiwave2 - automatically add a VLAN-tagged interface to the appropriate bridge VLAN
- wifiwave2 - exit sniffer command and return error when trying to sniff on an unsupported channel
- wifiwave2 - fixed 802.11r roaming for clients that performed initial authentication with an AP which has been restarted since
- wifiwave2 - fixed issue of some supported channels not being listed in the radio parameters
- wifiwave2 - fixed issue which lead to VLAN-tagged wireless clients receiving tagged traffic from other VLANs
- wifiwave2 - fixed key handshake timeout for re-associating client devices on 802.11ac interfaces
- wifiwave2 - fixed VLAN tagging for unencrypted (open) APs
- wifiwave2 - improved general interface stability
- wifiwave2 - improved regulatory compliance for hAP ax^2, hAP ax^3 and Chateau ax
- wifiwave2 - improved WPS connection speed
- wifiwave2 - increased maximum value for "channel.frequency" to 7300
- wifiwave2 - show information on captured packets and added ability to save them locally in a pcap file
- winbox - added "MTU" and "Hoplimit" properties under "IPv6/Routes" menu
- winbox - added "Preferred AFI" property under "MPLS/LDP-Instance" menu
- winbox - added "S" flag under "IPv6/Firewall/Connections" menu
- winbox - added "Tx Power" property under "Wifiwave2/Status" menu
- winbox - added "Tx Queue Drops" property under interface settings "Traffic" tab
- winbox - added "Username" and "Password" properties under "Container/Config" menu
- winbox - added "Valid" and "Preferred" properties under "IPv6/Address" menu
- winbox - added missing properties for "Remote ID Type" under "IP/IPsec/Identities" menu
- winbox - changed route flag name from "invalid" to "inactive"
- winbox - fixed "TLS" property under "Tools/Email" menu
- winbox - fixed "Type" property under "System/Disk" menu when "rose-storage" package is installed
- winbox - fixed changing slot name under "System/Disk" menu
- winbox - fixed default value for "Allow managed" property under "Zerotier" menu
- winbox - fixed duplicate "My ID" column under "IP/IPsec/Identities" menu
- winbox - fixed minor typo in "WifiWave2/Radios" menu
- winbox - fixed missing "Sector Writes" for certain devices under "System/Resources" menu (introduced in v7.8)
- winbox - improved Ethernet advertise, speed and duplex settings
- winbox - only show permitted countries for wifiwave2 interfaces
- winbox - show missing "Designated Bridge" and "Designated Port Number" monitoring data under "Bridge/Port menu
- www - allow unsecure HTTP access to REST API
- x86 - fixed changing software-id (introduced in v7.7)
- zerotier - upgraded to version 1.10.3