atom auto calibration
Auto-level. Sensor Wire. 6. 自動校正平台. 在首次列印前，或拆除過玻璃成型平台的話，強烈建議再次執行 ... 於官方支援網站下載「calibration box G-code」檔案。 ,Auto Calibration. Auto Level. Adjust Offset. Cool Down. Z Offset Value: X.XX. Prob Speed: XXX. Z Speed: XXX. (200°). ＊執行Restore Failsafe，需再執行Store ... ,Unload E1. Cool Down. (200°). (+660mm fast, +40mm slow). (+660mm fast, +40mm slow). Bed Leveling. Main ↑. Preheat ⇓(000°). Auto Calibration. Auto Level. ,Unload E1. Cool Down. (200°). (+660mm fast, +40mm slow). (+660mm fast, +40mm slow). Bed Leveling. Main ↑. Preheat ⇓(000°). Auto Calibration. Auto Level. ,Run [ Auto Calibration ], this step is only for firmware 20180329 ver. or later. Run [ Auto Level ]. Run [ Go to Zero ] or [ Adjust Offset ]. Place a regular copy paper ... ,(200°). (+660mm fast, +40mm slow). (+660mm fast, +40mm slow). Bed Leveling. 平台校正. Main ↑. Preheat ⇓(000°). Auto Calibration. Auto Level. Adjust Offset. ,更新：新增Auto Calibration（自動調平）. 適用於Atom 2.0, 2.5, EX, FX 機型，請使用Arduino 1.8.5 上傳韌體（韌體安裝教學請按此觀看）。 最後更新: 2018.Mar. ,點選[ Auto Calibration ] 進行自動調平。 * 此功能新增於韌體20180329 或更新版本，如使用舊版韌體則跳過. 再點選[ Bed Leveling ] 一> [ Auto Level ] 進行自動校正 ...
| 相關軟體 Atom 資訊 | |
|---|---|
 atom auto calibration 相關參考資料
ATOM 3 SERIES 使用者操作手冊 - ATOM 3D Printer
Auto-level. Sensor Wire. 6. 自動校正平台. 在首次列印前，或拆除過玻璃成型平台的話，強烈建議再次執行 ... 於官方支援網站下載「calibration box G-code」檔案。 http://www.atom3dp.com Atom LCD 180329 - ATOM 3D Printer
Auto Calibration. Auto Level. Adjust Offset. Cool Down. Z Offset Value: X.XX. Prob Speed: XXX. Z Speed: XXX. (200°). ＊執行Restore Failsafe，需再執行Store ... http://www.atom3dp.com Atom LCD 180529en - ATOM 3D Printer
Unload E1. Cool Down. (200°). (+660mm fast, +40mm slow). (+660mm fast, +40mm slow). Bed Leveling. Main ↑. Preheat ⇓(000°). Auto Calibration. Auto Level. http://www.atom3dp.com Atom LCD 181108en - ATOM 3D Printer
Unload E1. Cool Down. (200°). (+660mm fast, +40mm slow). (+660mm fast, +40mm slow). Bed Leveling. Main ↑. Preheat ⇓(000°). Auto Calibration. Auto Level. http://www.atom3dp.com Auto Leveling — Atom Support
Run [ Auto Calibration ], this step is only for firmware 20180329 ver. or later. Run [ Auto Level ]. Run [ Go to Zero ] or [ Adjust Offset ]. Place a regular copy paper ... https://atom3dp.squarespace.co 噴頭回到原點暫停列印狀態 - ATOM 3D Printer
(200°). (+660mm fast, +40mm slow). (+660mm fast, +40mm slow). Bed Leveling. 平台校正. Main ↑. Preheat ⇓(000°). Auto Calibration. Auto Level. Adjust Offset. http://www.atom3dp.com 機器韌體— Atom Support
更新：新增Auto Calibration（自動調平）. 適用於Atom 2.0, 2.5, EX, FX 機型，請使用Arduino 1.8.5 上傳韌體（韌體安裝教學請按此觀看）。 最後更新: 2018.Mar. https://atom3dp.squarespace.co 自動校正— Atom Support
點選[ Auto Calibration ] 進行自動調平。 * 此功能新增於韌體20180329 或更新版本，如使用舊版韌體則跳過. 再點選[ Bed Leveling ] 一> [ Auto Level ] 進行自動校正 ... https://atom3dp.squarespace.co |