HWMonitor 歷史版本列表
更新時間：2020-10-28
更新細節：
What's new in this version:
- MONITORING : moved the monitoring to a separate thread so that the interface won't freeze completly when monitoring takes some time to update
- MEMORY : made the memory allocation and initial fill single-threaded - this result in a slight delay in starting the test ( ~5s for 15GB), but lessen the "hang" on OCCT's Monitoring in the UI
- ENTERPRISE : fixed an issue with the report where the minimum displayed wasn't for the current period but for the report as a whole
更新時間：2020-10-22
更新細節：
What's new in this version:
- MONITORING : Fixed a problem with corsair commander devices / asus devices that could cause conflicts
- MONITORING : Decimal values are now displayed with 2-digit in the decimal part to avoid "jumpy" values in the UI
- ENTERPRISE : Reworked how the data were being pushed to the graphs to avoid an issue where the graphs would disappear if the UI was left IDLE after a test for too long (several hours) (tentative fix)
- ENTERPRISE : Fixed an issue where the X-axis of some graphs could be badly calculated, leading to either a missing graph or report in some cases
更新時間：2020-10-21
更新細節：
What's new in this version:
Event Graph Editor now also supports editing Poly Pressure. Besides selecting Poly Pressure from the selector menu, there are 3 new shortcut functions:
- Edit All Velocities = Switches the graph lane to show all velocities
- Edit Focused Key Velocities = Switches the graph lane to show the velocities of the currently selected key. (eg. handy for drum sequences)
- Edit Focused Key Poly Pressure = Switches the graph lane to show poly pressure of the currently selected key
- On top of these there also is an "Auto Follow Key" mode that auto switches the graph lane to show the relevant velocities / poly pressure
- You can toggle this "Auto Follow Key" mode via a right-click on the graph lane header
- Toggling that auto mode can also be done using a shortcut key to "Toggle Auto Follow Focused Key"
- Streaming audio files with a different samplerate than the current samplerate and with a data format different from 16 bit integer or 32 bit float did not properly work. Fixed
- When consolidating an audio sequence part, the audio lane mute/solo didn't work anymore. Fixed
- Zooming into an audio stream part could sometimes result in an incorrect empty waveform. Fixed
- When using many shortcuts some menus could popup slower. Fixed
- Sample displays: With very short samples (below 1000 samples) the Start/Loop/End sliders didn't work as expected. Fixed
- Sample Section Player -> Set Interpolation Mode did not work via a shortcut. Fixed
- The "Drag Parameter" function did not work via a shortcut. Fixed
- Monitoring keys of a multi-sample did not use the "Preview Monitor" rack if one exists. Fixed
- Mapping a meta-parameter to a module inside the Modular Feedback Delay could cause incorrect behavior. Fixed
- Live MIDI input: When note on and note off events arrive at the exact same time it could be that their order was switched. Fixed
- Sometimes monitoring audio was routed directly to audio out instead of Preview Monitor rack. Fixed
- In some cases the full zoom out (aka Overview) editor functions were not working correct from the first time, they needed a double trigger. Fixed
- New shortcut options for scrolling and zooming editors
- Other mini improvements
更新時間：2020-10-15
更新細節：
What's new in this version:
- Monitoring : Fixed a startup issue on Intel GPUs that were not reporting their allocated memory
- Enterprise : Fixed an issue that prevented the report from generating under some circumstances
- Enterprise : Fixed an issue where the reading were offset if OCCT was left idle between two tests, due to an issue in reseting a timer
- Enterprise : Added "?" wildcard support in selecting sensors
更新時間：2020-10-13
更新細節：
What's new in this version:
- Fixed an issue where the monitoring froze due to the memory allocation pass in the Memory test
- Fixed security values in the monitoring that are disabling sensors being too tight - they should be more lenient, leading to a better stability (at the cost of small "hiccups" in the graph update)
- Disabled the storage flags by default - OCCT doesn't really care about storage right now. You can enable them in OCCT's options
- Improved overall monitoring stability
更新時間：2020-10-12
更新細節：
What's new in this version:
- Main : switched to HwInfo as my monitoring engine
- Main : the code preventing OCCT to be launched twice is now working again
- Main : code cleanups and numerous bugfixes
- Ui : occt's ui is now split in 3 areas : Stability (for testing, the old view), SysInfo for system information, and Monitoring for a full view on monitoring
- Ui : this moves forced me to remove the expander (as it does not apply to every UI component)
- Ui : fixed the window default size to better accomodate the UI changes
- Testing : occt now tracks and reports WHEA errors that occurs during tests
- 3d : enabled tests to be run on displays without any display attached
- Vram : added slider, similar to Memory test, for selecting the amount of memory to test
- Monitoring : revamped the system usage report in the testing area - now supports several GPU, and with clickable buttons
- Monitoring : added "Current" sensor category
- Monitoring : added "Other" sensor category (without graph, obviously) (That's a lot of info, be warned)
- Monitoring : added usage graphs for Intel iGPUs (Thanks Сергей & Mew ! )
- Settings : added flags to control the monitoring - Enable and disable them at will in case of issues !
- Report : modified the report size and reorganized it to accomdate the monitoring update
- Enterprise : revamped the test report to include all the new features (and fixed a few typos)
- Enterprise : added a switch for giving a set of rules to OCCT to choose which sensor is enabled or not (see the help page for OCCT Enterprise for additional information)
- Enterprise : fine-tuned the monitoring rule engine to allow for customization in the enterprise edition
更新時間：2020-09-20
更新細節：
What's new in this version:
Features:
- Enhancement: #639 A new method is available which enables copying of multiple cells into a target layout while maintaining common subcells are single cells
- Bugfix: #637 Points have not been selected properly when inside mirrored subcells in partial edit mode
- Bugfix: #629 Qt5 QTimer timeout signal was not available to Python or Ruby. This also applied to all "private" signals of Qt5. QTimer is just one important example for this case
- Bugfix: #617 A problem with pseudo-const Python/Ruby objects in the netlist API was fixed
- Bugfix: #615 Basic authentication for package manager now uses UTF-8 encoding. Most servers expect this kind of encoding today. UTF password characters are supported this way
更新時間：2020-09-17
更新細節：
更新時間：2020-09-15
更新細節：
What's new in this version:
- UI : Minor graphical fixes
- TRANSLATIONS : Updated
更新時間：2020-09-07
更新細節：